Risager Bennetsen (yokeindia0)

As part of the search for biochemical markers of somatic embryogenesis in tissue cultures of olive (Olea europaea L.), peroxidases (POXs) in both the soluble and ionically wall-bound fractions were studied in two reputed olive cultivars (cvs.) "Picholine Marocaine" and "Dahbia". In order to carry out embryogenesis induction, proximal cotyledons were cultured in modified olive medium (OMc) supplemented with 25 μM indole-3-butylic acid (IBA) and 2.5 μM 2-isopentenyladenine (2iP), while distal leaf fragments (somatic explants) were cultured in OMc supplemented with 4.56 µM zeatin riboside (ZR) and 10.25 µM 1-naphthaleneacetic acid (NAA). Regarding embryogenic potentials, the zygotic explants (cv. Picholine Marocaine 43.39%; cv. Dahbia 53.41%) were more regenerative than the somatic explants (cv. Picholine Marocaine 13.05%; cv. Dahbia 19.51%). The enzyme assay showed a higher POX activity in embryogenic calluses (ECs) than in nonembryogenic calluses (NECs) for the zygotic explants in both studied cultivars. When expressed as units per milligram of proteins (U mg-1 proteins), the highest total POXs activities (soluble POXs + ionically wall-bound POXs) were found in the ECs derived from the zygotic explants; for cv. Dahbia, 65% of the enzyme activities came from the ionically wall-bound fractions. Polyacrylamide gel electrophoresis showed that the ECs of the highly active cv. Dahbia were characterized by highly active isoperoxidases that were revealed in four migration zones, particularly a doublet in the A4 zone (Rf 0.70-0.73) present in the ionically wall-bound POXs. The fast-moving anodic POXs of the ionically wall-bound fractions could be adopted as an early electrophoretic test to determine the embryogenesis capacities in olive tissue culture materials. As biochemical markers, the POX enzyme and its profile in fractions, i.e., as soluble POXs and ionically wall-bound POXs, can offer a valuable tool for improving the tissue culture of olive via somatic embryogenesis.In recent years, conjugated polymers have become the materials of choice to fabricate optoelectronic devices, owing to their properties of high absorbance, high quantum efficiency, and wide luminescence tuning ranges. The efficient feedback mechanism in the concentric ring resonator and its circularly symmetric periodic geometry combined with the broadband photoluminescence spectrum of the conjugated polymer can generate a highly coherent output beam. learn more Here, the detailed design of the ultralow-threshold single-mode circular distributed feedback polymer laser is presented with combined fabrication processes such as electron beam lithography and the spin-coating technique. We observe from the extinction spectra of the circular gratings that the transverse electric mode shows no change with the increase of incident beam angle. The strong enhancement of the conjugated polymer photoluminescence spectra with the circular periodic resonator can reduce the lasing threshold about 19 µJ/cm2. A very thin polymer film of about 110 nm is achieved with the spin-coating technique. The thickness of the gain medium can support only the zero-order transverse electric lasing mode. We expect that such a low threshold lasing device can find application in optoelectronic devices.The purpose of this study was to investigate the effect of retainer material and retainer position on a tooth to resist movement of the tooth in a simulation model. Bidirectional continuous glass fiber-reinforced composite (FRC) retainers and control retainers of steel wires were tested. The FRC retainers had a polymer matrix of bisphenol-A-glycidyldimethacrylate (bis-GMA) and poly(methylmethacrylate) (PMMA), and it was cured with a photoinitiator system. The retainers were adhered to a lower jaw Frasaco model in two different positions. Resistance against the movement of one tooth was measured from two directions. The average load values within the FRC retainer groups were higher than within the met